| |
CENTREPIN REEL REPLACEMENT BEARINGS |
| The bearings we offer
are quality selected to insure smooth running, low-torque start-up and spin. In our opinion and in cases noticed over the years, it's the outer bearing which usually obtains
the most wear and load while fishing and batting of the reel's drum,
as opposed to the inner back-plate side bearing. Lack of performance-spin of your center pin reel may be due to this bearing needing replacing and showing most wear due to rust-pitted balls and ring surfaces resulting from the harsh elements and the reel sitting for longer periods of time not being used.
A quick performance-test for wear of the bearings may be achieved, without the bearings being removal from the spool housing. Simply just separate the reel's spool from the back-plate, and once the bearing's inner rings are visible begin by just placing
the sharpened end of a pencil snug in the inner ring of
each bearing and while holding the outer rim of the spool slowly rotating the pencil back and forth to get the rings moving on the steel
balls, simultaneously paying close attention to any
excessive noise, rumbling and any slightest resistance being felt while races are in motion.
We are also able to match and supply any brand bearing available for most
centrepin reels in available rating from ABEC 1-9 from various manufacturers. Please email
us your inquiry stating application, rating and brand required for a quote.
Prices bellow -in all applications is for each bearing and not for a set.
CURRENT BEARINGS IN STOCK:
ADCOCK STANTON-MODELS 4.5" -and- 5" CENTREPINS
Made
in Japan, stainless steel, ABEC 5, dual shields, lube with light lithium grease. Note: Early model stanton center pins were manufactured utilizing a 3/16" overall diameter bearing spindle, as opposed to the later models which had an upgraded 1/4" OD spindle. Separation of the spool from the back-plate is recommended for a correct assessment prior to ordering. |
| |
JW YOUNG REELS ...PURIST II, JOHN WILSON HERITAGE &
BOB JAMES CENTREPINS |
Made
in the USA, stainless steel, ABEC 5, dual shields, greased with light machine oil. Note: JW Young reels are manufactured utilizing 2 different sized bearings resting in the outer and inner locations within the spool hub.. The bearing visible on the back-plate side of the spool is the larger size bearing. The inner bearing, sitting deep in the brass spool-hub, not in clear view is the smaller size bearing. When ordering please select both for a full replacement or as needed. as per selection below. |
| Price $25.95CAD
|
|
|
HANSON & MYKISS MKI & MKII CENTREPIN REELS |
| Made
in the USA, stainless steel, ABEC 7, dual shields, factory greased with light machine oil. |
| Price each: $22.95 CAD |
|
|
GLOOMIS, TOURNAMENT DRIFTER, STREAMSIDE, OKUMA AVENTA & SHEFFIELD CENTREPIN REELS |
| Made
in the Japan, stainless steel roller bearing, ABEC 3,
dual shields, light lithium grease lube. |
| Price each: $19.95
CAD Select Application: |
|
|
AURORA BARRINGTON 4.5" -and- 5" CENTREPINS |
Made
in Japan, stainless steel roller bearing, ABEC 3,
dual shields, greased with light lithium
grease. |
| Price
each:
$19.95
CAD |
|
|
|
 |
 |
SINGER SEWING MACHINE OIL |
Singer oil is a blend of
very thin and light colored oils. Its lubricant characteristics
and adhesive properties are unmatched in quality, allow
better penetration, polishing of metals, and lubrication for longer periods than
common oils. Sewing machine oil is highly recommended by
most centerpin reel manufacturers including JW Young &
Son's as their lube of choice for the proper maintenance
of roller bearings and mechanisms in their centerpins.
Comes in plastic bottle, 3.38 U.S. FL Oz. by volume. Made
in Brazil |
| Price:
$5.99
CAD |
|
|
 |

|
OKUMA NEOPRENE REEL CASE |
A quality crafted, robust
4mm thick neoprene reel case. Designed to fit 4.5”
diameter Centerpin reels on or off the rod, but with a little stretch also fits reels up to 5”
in diameter as well.
Picture shown covers a 5” Stanton on a GLoomis 1601-SK
float rod.
|
| Price:
$10.99 CAD |
|
|
 |

|
BARE SUPRA REEL CASE |
Black neoprene protective case for your
centerpin reel during transport, both on or off the rod.. Vertical split for ease of use.
Works with any rod & reel combination and pre-tested for best-fit
as indicated. Medium fits rod utilizing a 2.5”- 4.0”
reel and large fits rod with 4.5”- 5.5” reel.
|
|
|
|
|
 |


|
RAVEN REEL CASE
Custom designed, quality crafted neoprene reel case. Fits all Raven Centerpin reels, both off and on the rod during transport.
Price: $12.99 CAD
|
 |

|
CHOTA STL + BOOT REPLACEMENT CLEAT KIT |
Not to be confused with ordinary
sheet metal screws, Chota STL cleats are case
hardened steel and feature a specially designed head that
is dished out to form two semi-circular, deep biting blades.
Special "anti-back out grooves" on the flange
keeps the cleats securely seated to the
cleat base. (Required tool: ¼" nut driver.) Thread-length is 1 / 2" deep.
Note: Where felt-sole height allows, some steelheaders screw cleats directly on the felt-botom of regular non-studded boots, providing excellent results for traction, including long life. Exercise caution though and measure sole height twice.
|
| Price:
$9.99 CAD |
|
|
 |
 |
REPLACEMENT FELT KIT FOR STL+ BOOTS |
Same great wearing Chota felt but cut
for the "STL" Plus boot, with holes pre-cut for
the cleat bases, dark gray in color, available in sizes
9 through 14. For size not listed in selection, we can special
order.
|
| |
|
 |
 |
REPLACEMENT FELT KIT FOR All WADING BOOTS |
Offered by Chota, for their Abrams Creek Boot, However these felt soles work with most all felt-bottom wading boots. Dark gray polypropylene felt
kit comes with two die-cut soles and heels. Trimming is
necessary around the edges for best fit. Available in 2 sizes fits-all, men's 9 and smaller (medium selection)
men's 10 through 14 (large selection). Glue not included.
|
| |
|
 |
 |
QUICK LACE KIT |
Includes instructions and
all of the parts needed to replace The Quicklace™
System on one pair of Chota boots. Kit is also suitable for most all other types of lace-up wading or outdoor boots as well. Each shock cord lace measures 32" long.
|
| Price:
$9.99 CAD |
|
|
 |
 |
AQUASEAL WADER REPAIR |
Fixes and waterproofs neoprene rubber and coated fabric waders.
Offers permanent flexible repairs for all types of waders
and outdoor equipment. 1 oz. tube
|
| Price:
$9.69 CAD |
|
|
 |
|
|
 |